Paver Sealing & Sanding
Village Walk

Village Walk of Naples sits at Livingston Road and Vanderbilt Beach Road in 34109, behind a staffed gatehouse. DiVosta Homes built it in the 1990s, with a median build year of 1996, around lakes and canals crossed by Venetian-style bridges and miles of walkways.

Residents walk to the Town Hall center, with its clubhouse, fitness center, post office, salon and restaurant, and to three community pools. Owners’ own pavers carry part of that foot traffic every day, from the garage to the street walk.

Lake and reclaimed irrigation both appear in recent Village Walk listings. Communities on those sources often see rust-brown overspray soak into unsealed pavers along every sprinkler line.

Before sealing, we ask which irrigation supply reaches your zones, since listings here show municipal, lake and reclaimed water. A paver-safe rust remover is tested on one small area first, then applied to every arc, left to work and rinsed thoroughly.

Older paver areas lose joint sand to storms and cleaning, and in a community built for walking, uneven pavers on entries and walks become a trip hazard. Polymeric sand locks them back in place.

During the walk-through we press on suspect pavers. If one rocks, we check whether it only lost sand or has dropped below its neighbors; a paver that has sunk is lifted and reset on a leveled base before any sand goes in.

Joints that have emptied are cleared to at least 1 1/2 inches. Alliance Gator, a polymeric sand maker, warns against putting ordinary sand in the bottom of a joint and finishing it with polymeric, so the whole depth gets polymeric.

The sand only goes on once the surface is fully dry. We sweep, plate-compact, sweep again and compact again, and leave the sand about 1/8 inch below the paver’s top edge so the binder does not set on the face.

Water sets the bond. We wet one area at a time through a shower nozzle and keep it from drying mid-way; Alliance Gator’s G2 sands are made for that single watering and hold against rain after about 15 minutes over a draining base.

Walks and drives can take different sands. Alliance Gator steers driveway work to Gator Maxx G2 and keeps Gator Nitro and Gator Dust for areas without cars.

Sealer then closes the surface so overspray, leaves and tire marks stay on top, and restores color that years of sun have faded.

Sealer timing follows the label we use. SEK’s Surebond SB-6000 needs 24 hours after cleaning, activation or rain, air from 40 to 95°F and pavers below 120°F, with traffic after a day and full cure in seven. Techniseal’s water-based WA wants 30 days after polymeric sand, irrigation off and 48 to 72 hours before cars.

If you would rather not see a sheen, SEK’s SB-4000 is a breathable silane/siloxane that soaks in and repels water without forming a film. SB-1300 and SB-7700 are acrylic sealers that coat the surface and help hold joint sand, which also discourages weeds and ants.

Most homes here have a private pool and screened lanai, typically decked in pavers. We apply one coat of slip-resistant sealer around the pool; Techniseal notes a second coat on low-porosity pavers may become slippery.

White haze on joints after sanding is efflorescence. Alliance Gator connects it to humid weather or damp pavers at installation and removes it with an efflorescence cleaner or hot water under pressure, and we clear it before sealing so the coat does not trap it.

Most homes back onto a lake or canal. When we rinse a back deck, the runoff is pointed at the lawn so cleaner and loose sand stay out of the water.

Duplex villas here are generally two bedrooms plus a den with a garage, so the two drives on a building sit side by side. Each owner pays for their own side, and doing both together keeps the color even, which is the point of the callout above.

Single-family homes run three to four bedrooms on wider lots with longer drives. Those fall into the standard driveway row; a villa drive and lanai floor together often fit within the 400-square-foot package.

Homes here are Spanish-style stucco under tile roofs, often with plantings along the drive. Before any cleaner goes down we wet or cover the beds, shield stucco and garage doors, and rinse them again when the work is finished.

Re-sanding starts at $199 and clean with re-sand at $349. Clean, sand and seal starts at $399 for up to 400 square feet, $599 for a standard single-family drive and $499 for a slip-resistant pool deck.

We hold a Florida license and insurance and leave photos plus a written record of the products used. Call 239-544-1165, and we can schedule your neighbor on the same day.